- Characteristics : This is a smart BMS with UART or RS485 Communication which will be used to protect and monitor your battery status visible from the computer and your android APP phone .which can support parameters setting and adjustment .the charge and discharge port is same .
- Constant current : 150A or 200A
- Application ranges :6S to 20S Li-ion or Lifepo4 battery
- With one Build-in and two external temperature detection sensors
- Size: 202* 76 *18 MM
- with Multiple connection interfaces : LED power interface , RS485 or UART interface , Switch interface ,Bluetooth communication interface ,GPS module connection interface ,external temperature sensors interface. with heating pad connection interface
- SOC calculation and learning ability
- with one internal Temperature detection and one external temperature detector
- Support UART Communication : Voltage , Current ,SOC,SOH, temperature etc can be read
- With full sets of protection against your battery systems such as : over-charge , Over-current ,short-circuit , Over-discharge , High or Low temperature protection etc .
- With Mobile phone operation software systme to manage the detecting the battery working status and some parameters setting . also this board can be available for the PC operation and Parameters setting on the computer
- This BMS will includes such list :with one Bluetooth module for Android system and IOS system . with wire and connector for the Battery and Software system of mobile phone will be sent to the buyer .
reasonable order quantity .
Default Parameters setting 🙁 parameters can be adjusted via our APP and PC software flexible )
specification as below is our defaul setting value , clinet can use the PC module to set them on yourside without problems .if you want us to set it , you can leave a message to us based on your battery specification without problems
What Bluetooth Communication Module can do ?
IOS APP for apple devices :
PC communication and parameters display pages :
6S~21S connection methods in details
A. Firstly ,Please connect two bold wires from B- port of the BMS to the negative port of the battery pack .(B- wire should be as short as possible ) ,then connect these voltage detection wires (Please take off these wires from the BMS before connecting these wires to the battery to avoid any connection mistakes )
B. Second ,Please start connect these balance wires to the Battery system from BC0 ,Black thin wire should be connected to the battery negative , and the second wire -white wire BC1 should be connect to the positive port of the first series cell . BC2 should connect to the positive port of second series cell ,and BC3 wire to the third cell’s positive ….connection in this way in order one by one till to the last cell postive port
C. Third . After connection of these balance wires finished , please measure connector voltage from each Neighbouring wires ,the voltage between each neighbouring wires for Li ion battery should be less than 4V and for Lifepo4 Battery should be less than 3.5V ,after confirmation of these wires connection order , you can plug cable connector into the BMS .–wrong connection order will damage our BMS surely . please be carefully with this step .
D. Finally , connect C- wire as negative of charge and discharge , B+ wire as positive of charge and discharge , those wires should
use bold wire to make connection for large current distribution purpose . then please comparing the voltage from the BMS and voltage directly from the Battery to see if they are the same or not . if they are the same value . your connection is correct , otherwise terrible things will happend !!!
9) Precautions for use
1. When in use, design parameters and work conditions must be followed, and the parameters in this specification must not be violated, otherwise it is easy to damage the protection plate, and then damage the battery pack.
2. When in use, there should be corresponding electro static-free measures for testing, installation and contacting with the protection board.
3. The charging port can withstand the specified DC voltage. If the charger is higher than this voltage, it cannot guarantee that the protection board will not be damaged. Please use the charger according to this specification. It is better to choose the charger with the function of closing the trickle current at the end of charging current, so as to achieve double security. Chargers without trickle current closed are designed for lead-acid batteries and do not work with lithium.
4. When in use, Pay attention to the electric lead, electric soldering iron and solder splash. Do not enable them to touch the components and parts on the circuit board; otherwise the protection board may be damaged.
5. The maximum discharge current is the maximum current that lasts for a few seconds. During the test, it cannot last too long to avoid overheating damage of power MOS.
6. When assembling the protection board and the battery pack, do not place the heat dissipating aluminum plate close to the surface of the cell. Otherwise, the heat will be transferred to the cell, affecting the safety of the battery pack.
7. If abnormal conditions occur during use, please stop using it immediately, return it to the original factory or ask professional maintenance personnel for maintenance.
8. If it is a split protection board, it is forbidden to use P- as a charging port. Because P- is used as a charging port, the battery pack has no overcharge protection. It is forbidden to use C- as a discharge port at the time of splitting
9. It is forbidden to use two or more protection boards in series and in parallel.
10. The protection board has already done a lot of reliability tests, the reliability is far higher than the general protection board on the market, and the process of the cell must be ensured at the same time, so as to reduce the occurrence of combustion as much as possible.
11. This BMS does not have 0V charge function,the battery performance will be deteriorated seriously and even dead
12. In order not to damage the battery ,user should charge the battery periodically when the battery does not work for long time ( battery capaicty are more than 2Ah , storage time exceeds 3 months) ,after discharge compeltely ,please charge the battery in time within 12 hours to prevent the battery from discharge to 0Volt due to self-current consumption with the battery . client should label the battery with clearly battery manitenance instructions to improve the battery heathly .
13. please do not make reverse charge as this bms does not have anti reverse charge function .any reverse charge will damage our BMS probably
10) Safety Precautions:
Our company is committed to improvement of quality and reliability, but in general, there will be a certain probability of failure in electrical components and parts, with different environment and conditions, the durability will be different. When in use, the lengthy design is adopted to avoid overload abnormal fever, smoking, and even casualty, fire accidents, social damage, etc.
Reminds : We will send the detail connection drawings to the client with this product if client needs and this BMS will includes all necessories connectors with wire to make sure client can connect it easily . please follow up it correctly to avoid of any mistake ,above connection is only for simple explaination purpose .
1)Do not apply the PCB which beyonds the specified criterias as above :
2)Sometime , the battery may not discharge when connected this PCB , please connect it to the charge and it can recover to the normal status .
3)The PCB may not work normarly When Mixing cells which were over-discharged or over-charged ,
4) Do not shock this PCB with big static even though the PCB has been designed with anti-stastic protection function.
My distinuished customers : you can contac us through email or skype if you have any further questions with our product
Please choose the shipment way as you like ,you you can consider express delivery way if your order is urgent , but you
should afford the extra freight cost by express delivery .
As post by air ,usually it takes around 20-60 days ,please notice it and do not open the disputes easily before reaching the
contact with us ,we will try our best to solve the problem with our joint efforts .
We guarantee the product from us with a 12 months warranty against defects in quality, but we are not responsible
for buyers’ mistake or wrong handling, our product must be maintained in proper way. If Item is defective and not working
on arrival, please report the item to us within 7 days of receiving the defective product so we can issue a RMA.
Please contact us to request a return authorization. Please include your name, auction number, and reason for return when you
contact us. All items returned must contain all original packaging materials. Please carefully repack the item. Items returned will
be tested and if found defective, the buyer will be shipped a new replacement unit immediately. In the event that a suitable
replacement is not available a refund will be issued.
The return shipment cost should be afforded by buyer if you can not accept our policy ,please do not buy the item from us ,fair deal is importablefor both of us .Feedback
You satisfaction and positive feedback is very importand to us. Pleae leave positive feedback and 5 stars if you are satisfied with our items and services.
If you have any problems with our itmes or services, please feel free to contact us first before you leave negative feedback. We will do our best to solve any problems and provide you with the best customer services.
There are no reviews yet.